Print Page - Help On My 1984 KTM 125 MX Needed

Title: Help On My 1984 KTM 125 MX Needed
Post by: Tom Fox on March 30, 2010, 09:46:29 AM

Hi All:

Just recently purchased a 1984 KTM 125 MX project and was wanting to know what parts off of the 1984 250 MX are the same? Also does anyone have the Shop Manual 1984 KTM 125 MX I could get?

Thanks: [8D]

Tom

Title: Help On My 1984 KTM 125 MX Needed
Post by: brian kirby on March 30, 2010, 10:09:53 AM

Spring rates are different and the frame may be a little different, but most of the chassis is the same. Radiators are the same, seat, forks, triple clamp, shock except for spring rates and valving is the same.

Brian

'72 Berkshire

Title: Help On My 1984 KTM 125 MX Needed
Post by: Kip Kern on March 30, 2010, 11:46:13 AM

Call Al Buehner (suppliers), he may have one or a copy.

Title: Help On My 1984 KTM 125 MX Needed
Post by: G Ellis on March 30, 2010, 05:39:24 PM

Tom give me a call ,I have what you need. Later Gary 217 260 0237

Title: Help On My 1984 KTM 125 MX Needed
Post by: Tom Fox on April 03, 2010, 02:08:51 AM

Gary:

Do you have the parts manual for the engine for the 1985 and 1986 engine?

Also what would be the shipping for the MC Frame to Missouri? And do you have a nice swingarm bolt?

Thanks:

Tom

Title: Help On My 1984 KTM 125 MX Needed
Post by: Tom Fox on April 03, 2010, 02:09:38 AM

THat s a pivot boly that goes through the frame and swingarm.

Thanks:

Tom

Title: Help On My 1984 KTM 125 MX Needed
Post by: G Ellis on April 03, 2010, 11:17:25 AM

Just give me a call. Shipping will cost more than the frame. Later Gary

Title: Help On My 1984 KTM 125 MX Needed
Post by: brian kirby on April 03, 2010, 11:25:02 AM

Depending on where you are in Missouri it might be cheaper to drive to Gary's in Illinois rather than ship it. Plus you can buy lots more '84 KTM stuff from him you didnt even know you needed until you see it. :D

Brian

'72 Berkshire

Title: Help On My 1984 KTM 125 MX Needed
Post by: Tom Fox on April 05, 2010, 09:02:16 PM

Thanks Brian will be calling Gary to see when I can come up there.

Wanted to know if anyone had a clutch holding tool for the 125? Or what did you use to create one? Started dissassebling the engine to check bearings and seals. Long way to go. Anyone have a good source for lower end gasket set?

Thanks

Tom

Title: Help On My 1984 KTM 125 MX Needed
Post by: G Ellis on April 06, 2010, 12:34:23 AM

I have complete gasket kits. Later Gary

Title: Help On My 1984 KTM 125 MX Needed
Post by: Tom Fox on April 06, 2010, 12:56:19 AM

Thanks Gary will call on Wed if thats ok to see when is a good time to come up.

Thanks:

Tom

Title: Help On My 1984 KTM 125 MX Needed
Post by: Tom Fox on April 07, 2010, 06:19:54 PM

Also looking for a clutch holder. Any After MArket ones out there that work for this model?

Tom

Title: Help On My 1984 KTM 125 MX Needed
Post by: rob w on April 07, 2010, 10:01:44 PM

I take an old steel clutch plate and weld a handle onto it.

(http://i52.photobucket.com/albums/g8/BobWardlow/pog-1.jpg)

Title: Help On My 1984 KTM 125 MX Needed
Post by: firstturn on April 08, 2010, 08:48:00 AM

Great picture or should I say painting?

Ron Carbaugh

Penton Owners Group

General Discussion => Wanted / For Sale => Topic started by: Tom Fox on March 30, 2010, 09:46:29 AM