I am planning to bring the following to VMD for sale. If you are NOT attending
VMD and have interest in any of these, drop me a note at 3putt at hky dot com.
Actual shipping cost will be additional.
I wish to SELL these items, if you think the asking price out of line, drop me a note
or phone me 724-745-four two three one, and we can talk about it.
W Nelson McCullough
Here is a list of KTM Engine items for sale
175 cc cylinder head (black) with slight ring damage $15
73 JP clutch cover, black with external pitting $5
74 JP full mag cover, black with external pitting $5 SOLD
60 tooth rear sprocket (black power coat ) NEW condition, 8mm thick, 530 chain $25
1974 KTM 175cc cases good condition ser # 4-52 $150
1978 KTM 125cc cases very good condition ser # 8-51 $175
1976 KTM 250cc eng cases, need cleaned up ser # 6-54 $40 SOLD
1976 KTM 250cc bottom end, crank stuck, gear shaft turns, $165
KTM 250cc Cylinder head, slight combustion chamber ring damage $15
KTM 400cc Cylinder Head, slight combustion chamber ring damage $15
Quite a few KTM internal eng, tranny parts, bearings, etc, still in the boxes
Here is list of Sachs Engine items for sale
100cc Butch cyl head $5
125cc Butch cyl head $5
125cc Iron Cyl, High Compression Head $35
125cc ALLOY Head full fin, modified, 2 plug holes $20
100cc ALLOY Head 6 day overhead exhaust fin cut, modified 2 plug holes, $20
125cc ALLOY Steel Tank cut fin Cylinder 54.5mm very clean $45
100cc ALLOY Steel Tank Complete Top End, Cylinder, Head, with 49mm Piston/rings $95
Wiseco SACHS 125cc NOS piston kit (marked 168P6) 55.5mm, has intake window, thought to be for reed valve $70
Looking to Buy or trade for a good straight set of steel tanker wheels, Alum rims preferred, but will consider chrome steel.
Also wanting a good straight set wheels for early 72/73 CMF 6 day or Berkshire.
W Nelson McCullough
Nelson, Do you have a usuable 250 KTM cylinder? 74-77 or 78-8 style. Mike
Michael R. Winter
I enjoy rebuilding and appreciating Pentons!
1974 250 HS Pentons-1980 KTM 175-400'S
1975 Can Am 175 TNT & 77 250 Black Widow
1979 Husqvarna OR390
1976-78 RM & 77-79 PE Suzuki's
1974 CR250M 07 CR125R 79 CR250R
3putt, I'd like to take a look at the 100cc ALLOY Steel Tank Complete Top End, Cylinder, Head, with 49mm Piston/rings for $95. See you at the big top ;)
Dale Fisher
Penton Owners Group - Memberships
Facebook - Cheney Twinshock Racing Group - Administrator
'70 Six-Day 125 - V2017
'71 Six-Day 125 (Dave Fisher's) - V5553
'72 Mudlark - W257
'73 Jackpiner - 175 21159727
'74 Berkshire 100 - 40171056
And some silly other bikes...
I'll take the 74 250 cases, I'll call you this afternoon. & send an email. Scotty
Nelson,
Sent email regarding the 74 JP ignition cover.
Thanks,
Keith Meatyard
Mike,
I have a 250 cylinder that I can bring if you are needing one. A quick measurement with calipers shows 2.495" which should be standard bore. It has some rust on cylinder walls so will need bored but other than that looks good with all fins and rubber dampers intact. Let me know and I can pack it in the trailer.
Dave McCullough
Scotty, I made a typo error on the 250 cases, thry are 1976 and not 1974. I sent a reply to your personal email. Regards, Nelson
Scott, Sorry about the typo error and understand your desire to keep ser #'s the same. Nelson
Keith, I did Not get your mail, sorry. The POG site reply mail address does NOT work.
You will need to type in my mail address as set out in the 1st paragraph of the ad, or include yours, or a phone number where I can reach you. Thanks for interest, Nelson
Nelson,
I sent via my address for you that was already in my address book, but anyway, you can reach me as follows:
[email protected]251 946-3308
Keith Meatyard