Messages

Also Strictly Hodaka has some foam with perforated steel mesh inner that may work.ed

72 Monark - project    
76 Hercules 175 - project
possible Penton-Hiro project

Hello I think the Monark filter will work there are usually some for sale by the swap meet man on the bay. Ed

72 Monark - project    
76 Hercules 175 - project
possible Penton-Hiro project

Hi I got a set of instructions in a Sachs-Penton piston kit. It says to mount the piston put the cylinder on and scribe a line on either side of the bridge of the exhaust port on the piston. Drill a .040" hole through the piston in the center of the two scribe lines 7mm underneath the lower edge of rectangular ring grind the edges. Piston clearance  .04 to .045 mm max allowable clearance .06mm to .065mm. Piston ring clearance .1524mm to .2032mm max clearance .4572mm. Ed


72 Monark - project    
76 Hercules 175 - project
possible Penton-Hiro project

Hey give me a call LG.......

72 Monark - project    
76 Hercules 175 - project
possible Penton-Hiro project

You can reach me at [email protected] thanks again

72 Monark - project    
76 Hercules 175 - project
possible Penton-Hiro project

Do you have a 74 Penton 125 frame and swing arm looking for a November or December. Thank You Ed email eddiestimach@yahoo

72 Monark - project    
76 Hercules 175 - project
possible Penton-Hiro project

Just seen the post good topic I went into the garage and looked at my motor it is a Hiro motor it has the blue Penton badges on it I could not find any numbers like an engine serial number! The only numbers on it are like the Sachs case half numbers mine are 126 (stamped on the bottom in the back) should there be a serial number as well? Does anyone have any idea on how to service the motor how much oil it takes? I haven't pulled the cover on it yet what type of ignition does it have does anyone have a recommendation on type of coil to use? Ed

72 Monark 125cc        68 Penton 100cc         68 Zundapp 100cc

Thanks for the Info Ron. I will take the stuff to my lady this week Kevin,Ed

72 Monark 125cc        68 Penton 100cc         68 Zundapp 100cc

Hello Kevin at some point I am going to have a seat cover and the foam duplicated from a seat I have do you still need these items? I have no idea what my lady will charge but if you need a set I will have her make extra? Let me know Ed

72 Monark 125cc        68 Penton 100cc         68 Zundapp 100cc

Maybe not im in SFO!

72 Monark 125cc        68 Penton 100cc         68 Zundapp 100cc

Hey you guys need to Weigh-In before you can get in the Ring also what color trunks are you guys going to wear and what are the odds in Vegas. Donny I know you will be getting your frame but if they knock them selves out I have a May 72 frame and a airbox you can have. Have Fun Ed

72 Monark 125cc        68 Penton 100cc         68 Zundapp 100cc

Hey Ron Happy Birthday from Northern California,Ed

72 Monark 125cc        68 Penton 100cc         68 Zundapp 100cc

The tubes measure 22 1/8

72 Monark 125cc        68 Penton 100cc         68 Zundapp 100cc

Hey JP if they are same length as the 35mm forks from a Steel Tanker I have a set that look good. Give me a call Ed

72 Monark 125cc        68 Penton 100cc         68 Zundapp 100cc

Happy Birthday Mike and many more as well! What new Toy did you get yourself this year? Best of everything,Ed

72 Monark 125cc        68 Penton 100cc         68 Zundapp 100cc