Messages

David--did you get my e-mail on 1976 mc5.can send pictures and fill you in.   [email protected]

Denison tx.75021

earl m dempsey

evomx244---I have a 495 frame #8312 09804.Rolling frame comes with USD forks-tank-seat-engine and other parts e-mail me off site I can give you a better idea of whats there and condition. Price is good.

mxearl

earl m dempsey

Charles.  The fiber sleeve you need for a Bing 54.I have a sleeve i removed from a Bing 54  54/36/108. I checked another Bing 54 that i have 54/38/101 it has the same sleeve as the 36. These sleeves are not the thin fiber sleeves but looks like they are made from delrin material. The O.D. is 49mm and the I.D. is 45 mm, material is 23mm thick. The fiber sleeve is a lot thinner. I would send you one if you think it would work. I don't know why the sleeves are different somebody out there will.

mxearl



earl m dempsey

G Ellis.

I have a CMF case motor guard. It bolts up to the frame tabs and skid plate in front of the frame. This motor guard is bent back on left side no kinks looks like it could be an easy fix with a little heat. Thought you might want to try it. No charge on bad parts. Shipping only.

[email protected]
Earl Dempsey
Denison,Tx.

earl m dempsey

Allan.

I have a used air box for 82-83 KTM 495. Has a burned spot where pipe is close. There is a piece of asbestos glued in this area, and places burned through. Easy fiber glass repair.

Later.
mxearl

earl m dempsey

Phil.    Al Buehners service manual that I purchased has information on spec. sheet for KTM 125. It lists a 54/34/1040 Bing. Slide 230
pilot jet 40, main jet 170.

In the back of the manual there are some yellow spec. sheets for KTM 125. Bing carb listed on this sheet is 54/34/104.

230 slide
50 pilot jet
170-180 main jet
322 needle jet


Would you trade carb. for other penton parts. I have tanks for six days and most parts off of rollers. Some KTM PARTS.
Thanks mxearl


earl m dempsey

THANKS FOR THE HELP ON ENGINE ID. THE CASE DOESN'T LOOK LIKE A 1973 SO I'LL GO WITH THE 1983. ALSO THE CASE PART NUMBER VERIFIES THIS. NICE TO ONLY HAVE TO GO TO ONE SITE FOR EXPERT INFORMATION.

earl m dempsey

Wolffee,bob!.....thanks for the carb. info.I printed this so i can digest the information a little at a time. I have a drawer full of the rubber sewer pipe connectors. have used them before and they work fine......thanks again [email protected]

earl m dempsey

Parts Bike 350.00    frame # 831209804.....Engine # 563-30-003-200....engine has good compression...upside down adjustable 44mm forks....WP adjustable piggyback shock....front disc brake...missing rear rubber...pipe is no good....no top on bing carb...good parts bike....e-mail or call for pictures ..... 903 271 0173



earl m dempsey

My Dad and i are leaving Dallas on Thursday Sept 2nd and going to the swap meet in Davenport ,Iowa   we will return on Sunday Sept 5th  we can transport dirt bikes each way for 150.00 per bike  have references  former Penton/KTM dealers  call or e-mail mike   903 271 0173

earl m dempsey

Need a few things to finish this one .. also need boot from carb to airbox..this is an offset Intake Adapter #51.30.150500  
 for a 1976 mc5 125... will be used with a lectron ..this was a factory support bike.. please e-mail me at [email protected] and i will e-mail back my phone number
thanks
miked

Putting late model mikuni 32mm on jackpiner.Does anyone have a baseline i could work from.

Thanks
Earl

earl m dempsey

Scott, mail still will not go through.
mxearl

earl m dempsey

pentonpal
Scott you have mail from Texas.

earl m dempsey

This post is listed on Marks Motorcycle [email protected]

1971 steel tanker dissasembled. Several boxes of motor parts and two exhaust pipes $700.00
I have a 1971 steel tanker and don't need. Maybe someone on POG site could use.
mxearl

earl m dempsey