Messages

Thanks for the input so far. I probably should have mentioned I did indeed try reversing them, swapping them sise for side, and every other possible combination I could think of. It's got me stumped, you would think one of them would fit - unless neither is for this bike!

 

Thanks Larry, you pointed me in the right direction. I just found a photo on the allcustomfab website that shows the rear sidecover mount/pipe mount. It apparently does double duty as a mount for the side cover (where I don't have a mounting hole) and a rubber "spacer" sitting under the pipe. any other help as to the tiny bracket under the seat where the sidecover sits.

 

Hey Mikey,

Thanks for the info - sounds perfect!

 

POG members – this needs a home - don't really want to go to ebay.

1974 Penton 250 (red and yellow) - Barry Higgins motor, 71.5 piston, PVL ignition, 0 hours – hasn't even been started! Original title and manual. Original tank, side covers, exhaust, carb, air box and boot. All else is either new OEM or reproduction parts. Small box of "odd bits" included (original ignition, footpegs, etc.). Located in Central PA. $2100 firm. 0ver $ 3000 in new parts (with receipts). Sorry – no photos. Email me at: [email protected]

1974 Penton 250 MX (red and yellow) - 0ver $ 3000 in new parts (with receipts). Original title and manual. Barry Higgins rebuilt motor, 71.5 piston, PVL ignition, 0 hours – hasn't even been started! New OEM engine cases, engine side covers, clutch, and hubs with Akront rims and Buchannan spokes. Reproduction stainless footpegs, skid plate, petcocks, rear brake rod, chain guard, front and rear fenders, seat cover, front number plate, fork boots, and magura throttle assembly. Original tank, side covers, carb, air box and boot. Small box of "odd bits and parts" included (original ignition, footpegs, etc.). Located in Central PA. $2100 firm. Sorry – no photos. Email me at: [email protected]

 

Just rebuilt an original Bing carb from a 1974 250. Where should I set the throttle stop screw and air adjusting screw to get the bike started?  I think I can handle the fine tuning once it's running - but any suggestions are most welcome! Thanks in advamce.

 

Is anyone running aftermarket or accessory footpegs? If so, which ones and how did you mount them? Any help would be greatly appreciated.

Have an original CEV taillight, a red wire coil, and a rear brake light switch, all from a '74 250. Make a reasonable offer. email me at: [email protected]

My restored '74 Penton 250 now needs a new chain (#530). Unfortunately, I don't have an original to measure for length. I'm running a 12 front and a 55 rear sprocket combination. Can anyone tell me the correct length for this bike?

I have, what I believe to be, a pair of mint condition original footpegs for a 1974 250. Unfortunately, when mounted, they both angle back towards the rear of the motorcycle. Is this normal, am I missing some hardware, or am I simple missing the obvious? Any help would be greatly appreciated - including the use of other pegs.

Does anyone make seat stencil kits so you can put your brand on the back of your seat.

I know these are difficult to find, but is there a kickstart lever for a '74 250 out there anywhere?

 

Can anyone suggest a source for a set of stock handlebars for a '74 250? They don't have to be OEM/NOS - just the same dimensions. Thanks.

Help! My restoration project is coming slowly- but I've hit a snag. It was a basket case ('74 250), so I have no frame of reference and the manual is of no help. The right sidecover has only one bolt hole in the front - no problem. However, there is an "empty" bracket to the rear of the sidecover (below the pass through pipe) that would make a great attachment point. Is that what it is for (with an additional part) or is it for something else? How about the tiny bracket on the upper frame rail (below the seat) where the same sidecover goes on? What is that for? Any help would be greatly appreciated. Thanks.

 

Anyone know if there are spoke kits available for both front and rear wheels for a 1974 Penton 250? Thanks for the tips on finding new engine cases - found a great set!