tall bars

[shpclay]

Does anyone know where to get the old high point bars that had a tall bend to them?

Steve Clay
76 250 Penton/73 Harescrambler
76 husky 250 WR
2002 Aprilia Futura
71 Honda Trail 90

[socalmx]

Watch EBay, there is a guy selling vintage steel handlebars for around $25.

[shpclay]

thanks. I'll check it out. Wonder what bend or height they were. Just about everyone had them.

Steve Clay
76 250 Penton/73 Harescrambler
76 husky 250 WR
2002 Aprilia Futura
71 Honda Trail 90

[bkinnon]

Steve,

I was watching a set last week that went for $67. I wasn't high bidder, but here is the link to the auction. Hope it works. If it doesn't, I will get the ebayer's name and email if you would like.
It was item # 250065795024
Bill MacKinnon

http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&ih=015&sspagename=STRK%3AMEWA%3AIT&viewitem=&item=250065795024&rd=1,1


Downeast Pentons- Central Division

[DKWRACER]

Hi Poggers, at one time Jeff Tulinius was selling bars on Ebay. They had approx 6in rise and 5 in pullback. I think his email is: [email protected]. Also looked a JC Whitney's catalogue and they list MX bars that have a high rise and are slightly flatter. In another post, someone mentioned Paul Stannards bars as being close to the orig. Penton bars but sans the knurling, now that I think, believe it was Dwight...
BFN,
Tom Brosius

[DKWRACER]

Hi Poggers, Fly Racing Products has Vintage Bars that I saw today, they appear to be a very good copy of Bultaco Bars with approx 5.5 rise and 5 pullback... Here is a link:
http://www.ridegear.com/rg/item/F-22023/Fly_Racing__Aluma_Steel_Vintage_Bend_Handlebar_.html
Adios!
Tom Brosius

[shpclay]

Those are the ones. They were perfect for woods riding. They had a lot higher rise than 5 inches I believe.

Steve Clay
76 250 Penton/73 Harescrambler
76 husky 250 WR
2002 Aprilia Futura
71 Honda Trail 90

[rob w]

Steve,
Well I only have one pair of the original OEM bars, which I would like to hold on to.
But I have two pairs of the Inter-Am alum. bars in gold, in two slightly different bends, one very close to the originals you're speaking of, and the other pair is even taller and wider.
Let me know, I'll send them your way. $30 + shipping.

Bob

[cubfan1968]

Bob how wide are those OEM bars?

Rod Whitman
Omaha, Nebraska
1972 Six Day (Rider)
1972 Six Day (Project)

[rob w]

Rod,
 They're not the original width, they've been dewidtherized down to 31".

Bob

[rd400pi]

Hey, pullback is a tricky thing.  I have seen some bars on ebay that have enough pullback that they seem more suited for flattrack use.  Cheers.

  Mike H.
  Tulsa

[shpclay]

Bob, how tall were the original bars. Pro taper has one called ATV HI.
I would like some close to the original I wouldn't want the ones that are taller. I looked up the atv hi they are 6.3 high and 3.94 pull back, Is this close

Steve Clay
76 250 Penton/73 Harescrambler
76 husky 250 WR
2002 Aprilia Futura
71 Honda Trail 90

[linglewn]

Steve,
If you are looking for something that is close to original but not exact, you might try Strictly Hodaka. The last set that I used are from the Hodaka Wombat. They worked well for me. The only down side is that they aren't knurled at the triple clamp area. Paul at Strictly Hodaka is very helpful if you email or call him. Good luck.

Nelson Lingle
73 Jackpiner
71 DKW 125

[shpclay]

Thats pretty good. So the interam bars are fairly close. Are these the ones you want to sell?

Steve Clay
76 250 Penton/73 Harescrambler
76 husky 250 WR
2002 Aprilia Futura
71 Honda Trail 90