assorted items for sale

[Paul Danik]

I have been consolidating a lot of stuff to another location, am listing a few NOS items while in the process, all prices do not include shipping, shipping will be actual cost plus the cost of my coffee and a french donut... I have no interest in shipping out of the country, probably will do so if asked to do so, but I would rather be pruning the dead branches out of a dwarf conifer than standing in line at the post office...

NOS Sachs engine cases for the 5 speed "A" engine  These have the short studs for bolting on the cast iron cylinder.  $ 200.00

NOS Sachs clutch assembly. $ 100.00   SOLD

NOS  Sachs "B" crank assembly with steel rod, no main bearings.
$200.00   SOLD

NOS Sachs 100cc liner and NOS 48mm piston kit, including rings, wrist pin and circlips.  $ 125.00

NOS Sachs hi-compression head for cast iron cylinder, still in the box. $ 85.00  SOLD

NOS Sachs alloy full finned cylinder. The bore has been coated with grease for many years and will still need to be honed to clean it up when fitting the piston.  $ 150.00  

NOS Bing carb, 24mm.  1/24/153 this is the complete unit including the choke inner cable.  There is no throttle inner cable. $ 200.00

SACHS NOS Aluminum rod.  If you are building a 152cc engine using the old Yamaha 305 piston you will need this style of rod as the wrist pin bushing needs to be reamed for the larger Yamaha wrist pin. $ 50.00

Sachs 125cc liner still in the wrapper.  This is one of the ones made up a few years back.  $ 100.00

NOS Elko 400cc Standard bore piston kit, 81mm, including piston, rings, wrist pin and circlips. $ 100.00

NOS Sachs 55.5 mm 125cc piston kit.  This kit includes the piston, rings and wrist pin, don't see any circlips. Piston is stamped 55.43, this piston was made in Western Germany and is what the dealers used "back in the day". $ 100.00

NOS liner and piston kit for the 175cc 6 speed Sachs engine, this is the engine based on what visually looks like the Sachs engine in the Pentons. Includes NOS Liner, Elko piston, rings, wrist pin and circlips.  $ 175.00

NOS Torque Engineering down pipe for the Sachs powered Steel Tank Penton. Has round end for use with the alloy top end. This pipe is NOS, it has minor shelf wear and could use a coat of paint, but it is beautiful and unused. $ 385.00  SOLD

[email protected]  

Thanks,
Paul

[checkcrew]

Paul, hi,

i will take the NOS 125B crank assy.,

could you bring it to the PVR swapmeet in a few weeks and i will pick it up from you there ?

please let me know,

regards,

Mike Gallagher, NJ.
[email protected]

[SouthRider]

Paul - I would like the NOS clutch. I would also like to talk with you regarding the aluminum rod &/or the 175 liner kit for a project that I have in mind.

Please give me a call when you can.

Clark 9856303333

_____________________________________________________________________________________

"We the willing, led by the unknowing, are doing the impossible, for the ungrateful. We have done so much, for so long, with so little, that we are now qualified to do almost anything, with nothing."

1972 Penton Berkshire 100
1983 Husqvarna 250 XC
2011 Jayco 31.5 RLDS
2009 Chevy 2500 HD Duramax

[Paul Danik]

Mike,
Will do.Thanks.  

Clark, tried to call....will try again later.
Thanks,
Paul

[checkcrew]

10-4 Paul,
see ya there :-)

thanks,

Mike Gallagher, NJ.
[email protected]

[iyaoyas]

Hi Paul,

I know this may be a long shot but.....please keep your eyes open for a Wassell fuel tank and muffler.  I'm interested in gently used or NOS parts.  I'm also looking for other small bits & pieces for my Wassel such as a rear brake cable and chain oiler.  Thanks...!


Thanks-
Stephen Markley

[Dale Fisher]

Paul,
Reserve the Torque pipe for the moment until we can talk at the meeting about something you were looking for

Dale Fisher
Penton Owners Group - Memberships
Facebook - Cheney Twinshock Racing Group - Administrator

'70 Six-Day 125 - V2017
'71 Six-Day 125 (Dave Fisher's) - V5553
'72 Mudlark - W257
'73 Jackpiner - 175 21159727
'74 Berkshire 100 - 40171056
And some silly other bikes...

[joe novak]

Paul,   I am in need of a Steel Tanker exhaust pipe and air box assembly.   I have several project bikes all in need of them.  68, 69, 70, 71.  Thank you in advance for looking.   joe

[Paul Danik]

Steve,  Not much Wassell stuff left but I will keep an eye out.

Joe,  If your talking the Husky Style air cleaner I can most likely help you.  

Thanks,
Paul

[Lew Mayer]

Looking for two brake arms for a Wassell.

Lew Mayer

[t20sl]

Paul:
Pruning is always easier when performed with a Stihl 24" chainsaw.
Ted

[joe novak]

Paul,  Yes, the Husky style air cleaner assembly is what I need.   Thank you,  joe

[SouthRider]

Paul,

Did you get my email with my address?

Clark

_____________________________________________________________________________________

"We the willing, led by the unknowing, are doing the impossible, for the ungrateful. We have done so much, for so long, with so little, that we are now qualified to do almost anything, with nothing."

1972 Penton Berkshire 100
1983 Husqvarna 250 XC
2011 Jayco 31.5 RLDS
2009 Chevy 2500 HD Duramax

[Paul Danik]

Yes I did.
Paul

[iyaoyas]

Thanks Paul...appreciate any & all help as I'm wanting to finish this project in time for this year's VMD @ Mid-O

-Stephen